XXL Kit for Arduino · Wrap-up
Part 25 The end of the series: what you can do now and what's next
- Beginner
- Ages 8+
- about 15 min
Twenty-four tutorials ago you opened a box full of parts, and most of them did not even have a name you could pronounce. Today there is not a single thing in that same box that you have not connected and programmed. This part has no wiring diagram and no code. It is a summary of what you can do, and a map of what you can do with it next.
Who is it for? For everyone who has made it to the end of the series, and for teachers looking for a list of the skills this series really gives.
01
Congratulations
Seriously. Most kits for learning electronics end up in a cupboard after three parts.
You have worked through twenty-four tutorials, from lighting up a single LED to an alarm clock that stays on your desk and wakes you up in the morning. On the way you connected all 36 parts from the box. Each of them has its moment in this series, with one exception: the organizer box, which is simply a box.
But the persistence that counts here is not how many parts you got through. It is the moments when:
- the circuit did not work and you had to check sixteen jumper wires one by one,
- the program compiled, but the display showed nothing but rectangles,
- the LEDs lit up “in negative”, because the matrix turned out to be a different type from the one the text assumed,
- something got hot and you had to cut the power faster than you could think.
Each of those moments was annoying. And each one taught you more than a part that worked the first time.
02
What you can do now: hardware
A list to look over when you start a new project and wonder whether you can manage it.
| Skill | Parts |
|---|---|
| Build a circuit on a breadboard and read a wiring diagram | 4, then all of them |
| Light up an LED and know why it always goes with a resistor | 4, 5 |
Read a button without any extra parts (INPUT_PULLUP) | 5 |
Measure a voltage and turn it into a number (analogRead, voltage divider) | 5, 18, 19 |
| Get any sound you like out of a buzzer and play a melody | 6, 20, 22 |
| Control movement: a servo (angle) and a stepper motor (steps), and know when to use which | 7, 8, 11, 22, 23 |
| Show digits on a 7-segment display and understand multiplexing | 9, 13 |
| Draw a picture and an animation on the 8x8 LED matrix | 10, 12, 14 |
| Save pins with a shift register: 3 instead of 8 | 13, 14 |
| Detect movement, light, sound, water, fire, temperature and humidity | 15, 17, 18, 19 |
| Recognize a proximity card and switch a circuit with a relay | 16 |
| Show text on the LCD and connect a module with just two wires (I2C) | 17, 23, 24 |
| Handle a matrix keypad: 16 keys on 8 pins | 20, 23 |
| Receive the signal from an IR remote | 21 |
Mix a color on the RGB LED and dim it smoothly (analogWrite) | 21 |
| Keep real time with the RTC module and power a project from a battery | 24 |
And one more thing that is easy to forget. You know four different ways modules talk to an Arduino: UART, SPI, I2C and the DS1302's own three-wire protocol. Next time you see a new module, the first question, “how does it talk?”, will not be a mystery to you any more.
03
What you can do now: programming
This is the part that stays with you, even if you never touch an Arduino again.
| Skill | Parts |
|---|---|
if, loops, switch: making decisions in code | 3, then all of them |
| Variables and arrays: keeping many values under one name | 9, 10, 20 |
| Parallel arrays: several lists read with the same number | 22 |
| Your own functions: splitting a program into pieces with names | 20, 22, 23, 24 |
millis() instead of delay(): doing several things at once | 9, 10, 22, 24 |
| Detecting the moment a button is pressed, not how long it is held | 8, 23, 24 |
| Modes of a device: a program that behaves differently in different states | 23, 24 |
Joining text with the String class and laying it out on a display | 23, 24 |
| Saving to the permanent EEPROM memory: data that survives switching off | 14, 24 |
| Using other people's libraries and reading their documentation | 16, 17, 20, 21, 24 |
| Calibration: a program you fine-tune to your own piece of hardware | 18, 19, 22, 24 |
04
The most important thing that is not on the parts list
If you were to keep just one thing from the whole series, I'd like it to be this one.
In every part, before the real program appeared, there was a test: checking the wiring, reading the raw values from a sensor, printing the code of a button on the remote. That was not filler. It is the method every engineer uses, and it always looks the same:
- 1Don't assume: check. Before you build the whole thing, make sure the smallest piece works.
- 2Change one thing at a time. If you move three wires and swap the code, you won't know what helped.
- 3Read what is printed on the module, not what you remember. The marks
S,-,+on the IR receiver orR1,R2,R3on the RGB LED module can knock down the nicest theory. - 4If something gets hot or smokes, unplug it first and think afterwards.
- 5Documentation can be out of date. Libraries change versions, modules differ from batch to batch, and instructions written a year ago may describe something different from what you are holding in your hand.
This list works just the same with an Arduino, when you fix a bike, and when you hunt for a bug in a program you will write ten years from now in a completely different language.
05
What's next
Three levels, depending on how much time and energy you have.
Level 1: still from this box
Three projects made only of things you already know how to do. You don't need to buy anything or read a new tutorial.
| Project | Made of | New challenge |
|---|---|---|
| Electronic safe | keypad (Part 20) + RFID (Part 16) + servo (Part 7) + LEDs + buzzer | two different ways to open one lock: a PIN code or a card |
| Universal remote | IR remote (Part 21) + relay (Part 16) + servo (Part 7) + RGB LED (Part 21) | one remote controlling three devices at once |
| Home alarm center | flame and water level sensors (Part 18) + vibration sensor (Part 15) + LCD (Part 17) + RGB LED + buzzer | three dangers gathered on one screen, with colored signals |
Level 2: outside the box
- Move the project off the breadboard for good. A perfboard, a soldering iron and a case turn a prototype into a device that does not fall apart when you carry it around. The alarm clock from Part 24 is the perfect first candidate.
- Buy a sensor that is not in the kit. A distance sensor, a soil moisture sensor for a flowerpot, an accelerometer. Each of them connects exactly the way you have done it before: power, ground, signal, and a library.
- Power the project for longer. The 9 V battery from Part 24 lasts for hours. A power bank, a rechargeable battery or a solar panel lasts for weeks.
Level 3: beyond Arduino
FlashESP, which you have used throughout the series, programs not only the R3 board but also ESP32 and ESP8266 boards. It is the same way of writing code (setup(), loop(), digitalWrite()), but with Wi-Fi on board. Your alarm clock could fetch the exact time from the internet by itself, and the temperature sensor from Part 17 could send its readings to a page you open on your phone.
It is the natural next step: the same skills, a much bigger playground.
06
Show what you have built
Nothing makes knowledge stick like explaining it to someone else.
Before you take your last circuit apart, do three things:
- 1Record a video or take a photo. In a year you won't remember what it looked like, and this is your portfolio.
- 2Show it to someone and explain how it works. A parent, a brother or sister, a classmate. The moment you have to explain to someone why an LED needs a resistor, you find out whether you really understand it.
- 3Write down what did not work and how you fixed it. It is the most valuable note you can leave for your future self, and for others.
If you are a teacher: this series is arranged so that each part fits into one lesson, and the projects in the “Projects” section at the end of each part make good homework and extra tasks for faster students.
Summary
The XXL Kit is thirty-six parts. But the real content of this box is something else: the belief that when something does not work, it is not because “it can't be done”, but because you have not found the cause yet. And that the cause can be found.
Thank you for going all the way to the end. Now the most interesting part is only just beginning, because from this moment on nobody tells you what to build.
Good luck. Keep the resistor with the LED.