Back to Explorer

esp32-inmp441-example

Project Information

Author

Mikrobot.pl

Board

ESP32 Dev Module

SDK Version

3.3.2

Platform

ESP32

Created

Updated

Description

Check INMP441 microphone with ESP32

Flash to Device

Login required: You need to login or create an account to flash this project.

Sorry, your browser doesn't support Web Serial.Web Serial requires HTTPS.

README

ESP32 INMP441 Captive Portal

Monitor INMP441 I2S microphone channels via WiFi with a captive portal

This project turns an ESP32 Dev Board into a small WiFi-based audio level monitor.
When powered, the ESP32 creates an open WiFi Access Point and a captive portal.
As soon as a device connects to the AP, a web page appears that shows the live signal level from an INMP441 I2S microphone.

The web interface displays both I2S stereo channels:

  • LEFT channel
  • RIGHT channel

Important: one INMP441 microphone is a mono microphone.
It can transmit on either the LEFT or RIGHT I2S channel, depending on the L/R pin connection.
To get real LEFT and RIGHT audio at the same time, you need two INMP441 microphones.


โญ Features

  • Open WiFi Access Point (no password)
    • SSID: ESP32-INMP441
  • Captive portal
    • Any URL request is redirected to the audio monitor page
    • Works with Android / iOS / Windows / Linux
  • Web-based audio level monitor
    • Shows LEFT channel level
    • Shows RIGHT channel level
    • Shows percentage level
    • Shows dBFS value
    • Shows raw RMS value for debugging
  • I2S microphone support
    • Designed for INMP441
    • Reads 32-bit I2S samples
    • Supports LEFT / RIGHT channel detection
  • No external network or internet required

๐Ÿ“ฆ Hardware requirements

  • ESP32 Dev Board
    Example: ESP32-DevKitC, ESP32-WROOM development board
  • INMP441 I2S microphone module
  • Jumper wires
  • Breadboard recommended

๐Ÿ”Œ INMP441 pinout

Typical INMP441 module pins:

INMP441 pin Description
VDD 3.3V power
GND Ground
SCK / BCLK I2S bit clock
WS / LRCL I2S word select / left-right clock
SD / DOUT I2S audio data output
L/R Channel select pin

๐Ÿ”ง Default wiring: one INMP441 microphone

INMP441 ESP32
VDD 3V3
GND GND
SCK / BCLK GPIO 26
WS / LRCL GPIO 25
SD / DOUT GPIO 33
L/R GPIO 27

In this version, the L/R pin is connected to GPIO 27.

The code controls GPIO 27 automatically:

#define MIC_LR_PIN 27

You can select the microphone channel in code:

#define MIC_CHANNEL_RIGHT true

Channel behavior:

Code setting L/R state Active channel
MIC_CHANNEL_RIGHT false LOW LEFT
MIC_CHANNEL_RIGHT true HIGH RIGHT

๐ŸŽ™๏ธ One microphone vs two microphones

One INMP441 microphone

One INMP441 is a mono microphone.

It can appear as:

  • LEFT channel, or
  • RIGHT channel

but not both at the same time.

L/R pin state Microphone appears as
LOW / GND LEFT channel
HIGH / 3.3V RIGHT channel

The web page will still display both channels, but only one channel will normally react to sound.


Two INMP441 microphones

To get both LEFT and RIGHT channels working at the same time, use two INMP441 microphones.

Signal LEFT microphone RIGHT microphone
VDD 3V3 3V3
GND GND GND
SCK / BCLK GPIO 26 GPIO 26
WS / LRCL GPIO 25 GPIO 25
SD / DOUT GPIO 33 GPIO 33
L/R GND 3V3

Both microphones share the same I2S bus:

SCK
WS
SD
3.3V
GND

Only the L/R pin must be different.


โš ๏ธ Important power note

The INMP441 must be powered from 3.3V only.

Do not connect VDD to 5V.

If you only have one visible 3V3 pin on your ESP32 board, you can split it using a breadboard or jumper wire.

For example, the same 3V3 pin can power:

  • VDD of the microphone
  • L/R pin of the right-channel microphone

The L/R pin uses almost no current.
It only reads a HIGH or LOW logic level.


๐Ÿ“š Required Arduino IDE setup

Install the ESP32 board package:

  1. Open Arduino IDE
  2. Go to Tools โ†’ Board โ†’ Boards Manager
  3. Search for:
esp32
  1. Install:
esp32 by Espressif Systems

No extra libraries are required from the Arduino Library Manager.

The project uses libraries included with the ESP32 Arduino core:

#include <WiFi.h>
#include <WebServer.h>
#include <DNSServer.h>
#include "driver/i2s.h"

๐ŸŒ WiFi access point

Default WiFi network created by the ESP32:

ESP32-INMP441

The network is open and does not require a password.

Default ESP32 access point IP address:

192.168.4.1

If the captive portal does not open automatically, open this address manually in a browser:

http://192.168.4.1

๐Ÿ–ฅ๏ธ Web interface

The web page displays:

  • LEFT channel level
  • RIGHT channel level
  • Percentage level for each channel
  • dBFS value for each channel
  • RMS value for each channel
  • ACTIVE indicator when a channel receives signal

The values refresh automatically every 300 ms.


๐Ÿ“ What is dBFS?

The displayed dB value is dBFS, not real-world sound pressure level.

dBFS means:

decibels relative to full scale

It shows the level of the digital audio signal inside the ESP32.

This is useful for checking:

  • whether the microphone works
  • which channel is active
  • whether the signal changes when sound is present
  • whether the wiring is correct

It is not a calibrated dB SPL or dB(A) measurement.


๐Ÿงช Testing

Test with one microphone

  1. Upload the code to the ESP32.
  2. Open Serial Monitor at:
115200 baud
  1. Connect to WiFi:
ESP32-INMP441
  1. Open:
http://192.168.4.1
  1. Make sound near the microphone.

If MIC_CHANNEL_RIGHT is set to:

#define MIC_CHANNEL_RIGHT true

then the RIGHT channel should react.

If it is set to:

#define MIC_CHANNEL_RIGHT false

then the LEFT channel should react.


Test with two microphones

Use two INMP441 modules:

  • LEFT microphone: L/R connected to GND
  • RIGHT microphone: L/R connected to 3V3

Both microphones should then react independently on the web page.


๐Ÿ› ๏ธ Troubleshooting

The page opens, but both channels show 0%

Check:

  • VDD is connected to 3V3, not 5V
  • GND is connected correctly
  • SCK is connected to GPIO 26
  • WS is connected to GPIO 25
  • SD is connected to GPIO 33
  • The microphone is an INMP441 or compatible I2S microphone

Only LEFT or only RIGHT moves

This is normal if you use only one INMP441 microphone.

One INMP441 can transmit on only one channel at a time.

To get both channels moving at the same time, use two microphones.


The wrong channel moves

Change this line:

#define MIC_CHANNEL_RIGHT true

Use:

#define MIC_CHANNEL_RIGHT false

for LEFT channel.

Use:

#define MIC_CHANNEL_RIGHT true

for RIGHT channel.


Captive portal does not open automatically

Manually open:

http://192.168.4.1

Some phones or laptops may not automatically show captive portals every time.


๐Ÿ”ข Default pin configuration

#define I2S_WS   25
#define I2S_SCK  26
#define I2S_SD   33

#define MIC_LR_PIN 27

Pin meaning:

Define ESP32 GPIO Function
I2S_WS GPIO 25 Word select / LR clock
I2S_SCK GPIO 26 Bit clock
I2S_SD GPIO 33 Audio data input
MIC_LR_PIN GPIO 27 Microphone LEFT / RIGHT select

โœ… Summary

This project creates a WiFi captive portal on an ESP32 and displays live audio levels from an INMP441 I2S microphone.

Use one microphone to test either LEFT or RIGHT channel.
Use two microphones to get real stereo LEFT and RIGHT monitoring.

Default WiFi:

ESP32-INMP441

Default web page:

http://192.168.4.1