# esp32-E18-D80NK-wifi

> Check an E18-D80NK proximity sensor live via WiFi with a captive portal

- Author: Mikrobot.pl
- Platform: ESP32
- Board: ESP32 Dev Module (`esp32:esp32:esp32`)
- SDK version: 3.3.6
- Tags: #esp32, #example, #captive portal, #wifi, #e18-d80nk
- Created: 2026-08-05
- Updated: 2026-08-19
- Favorites: 0, forks: 0
- Project page (view, flash from the browser, fork): https://flashesp.com/explore/C8kfKbqYwRXrBgIqmK9yx
- Download all sources (zip): https://flashesp.com/api/public-projects/C8kfKbqYwRXrBgIqmK9yx/download-sources/

## Source files

- [main.ino (8.0 KB)](https://flashesp.com/explore/C8kfKbqYwRXrBgIqmK9yx/files/4Y54qP2YyqOdGErc6O1P8.md)
- readme.md (3.7 KB)

## README

# ESP32 + E18-D80NK — Captive Portal Proximity Tester

<table>
  <tr>
    <td><img src="https://i.imgur.com/jvFQVSO.png" alt="Example usage" width="350"></td>
    <td><img src="https://i.imgur.com/sPwzVmj.png" alt="Example usage" width="350"></td>
  </tr>
</table>


This project turns an **ESP32** into a **Wi-Fi captive portal** that shows the **live state of an E18-D80NK** infrared reflective proximity sensor (NPN, 5–80 cm).
After connecting to the ESP32's Wi-Fi network, any URL redirects to the portal page, where you can see whether the sensor currently detects an object — a quick way to confirm the sensor simply works.

## Features
- Captive portal (AP + DNS redirect)
- Live detected / clear status with colored indicator (auto-refresh)
- Detection counter + "how long in current state" timer
- Simple settings in the portal (label + refresh interval)
- Works **without an external Wi-Fi network** (ESP32 runs as an Access Point)

## Hardware
- ESP32 development board
- E18-D80NK IR reflective proximity sensor (3 wires)
- (Optional) 10 kΩ resistor — only if you don't use the internal pull-up

No level shifter is needed. The sensor's output is **open-collector NPN**: it only pulls the line to GND when an object is detected, so a 3.3 V pull-up on the ESP32 side is enough. The 5 V supply never reaches the GPIO.

## Wiring (MOST IMPORTANT)

The E18-D80NK has 3 wires:

| Wire    | Function | Connect to ESP32 |
|---------|----------|------------------|
| Brown   | VCC      | **5V / VIN** (sensor needs ~5 V) |
| Blue    | GND      | **GND** (common ground) |
| Black   | OUT      | **GPIO4** |

### Schematic

```
        ESP32                         E18-D80NK
   +--------------+                  +-----------+
   |          5V  |------------------| VCC (brown)
   |         GND  |------------------| GND  (blue)
   |       GPIO4  |------------------| OUT  (black)
   |              |
   | (internal pull-up to 3V3 enabled in code via INPUT_PULLUP)
   +--------------+

   Optional external pull-up if not using INPUT_PULLUP:
   GPIO4 ----[ 10k ]---- 3V3
```

**Logic (default NPN):**
- Object detected → OUT pulled **LOW**
- No object → OUT floats **HIGH** (held high by the pull-up)

### Pin choice warning
Use a GPIO that has an internal pull-up. **GPIO 34–39 are input-only and have NO pull-up** — don't use them here (or add an external 10 kΩ pull-up to 3V3). Good choices: GPIO 4, 5, 18, 19, 21, 22, 23, 25, 26, 27, 32, 33.

## How to use
1. Flash the sketch to the ESP32.
2. Connect your phone/PC to the Wi-Fi network: **esp32-e18-d80nk**
3. Open any website (or go directly to **http://192.168.4.1**)
4. Wave your hand / an object in front of the sensor:
   - **OBJECT** (green) = sensor detects something
   - **clear** (red) = nothing detected
5. The E18-D80NK also has a small **potentiometer** on the back — turn it to adjust detection distance (5–80 cm).

## Customization
- Change the sensor OUT pin in code:
  - `static const uint8_t SENSOR_PIN = 4;`
- If your module's logic is inverted (detected = HIGH), set:
  - `static const bool DETECTED_IS_LOW = false;`
- Adjust refresh interval in the web form (100–10000 ms).

## Notes / Troubleshooting
- **Always shows "OBJECT":** wire is likely floating — confirm `INPUT_PULLUP` (default in code) or add the external 10 kΩ pull-up, and check the OUT wire is really on GPIO4.
- **Never detects:** confirm the sensor is powered from **5 V** (not 3.3 V — most E18-D80NK need 5 V), share a **common GND**, and adjust the potentiometer on the sensor.
- **Random flicker:** shorten the sensing distance with the potentiometer; IR reflective sensors can be fooled by very dark, matte, or angled surfaces.
- **State seems stuck:** the ESP32's onboard LED / Serial monitor at 115200 baud can help — the boot log prints the AP IP and the sensor pin.
